By Hiccup on 03-31-15, 01:10 pm |
Category 'Event controllers', known, fully documented |
This sprite shares its image file with P-switch, ? switch and Bowser battle switch. |
Data files: • /obj/I_switch_ncg.bin |
Sprite fields: • Triggering Event ID: value at nybble 0-1. [confirm latter sentence] If this ID is set, the Switch will only show while this Event ID is activated. Slightly buggy if used with Multi Use. [confirm latter sentence] • Target Event ID: value at nybble 2-3 • Falls, Loads at Midway: list at nybble 4: 0=None,1=Falls,4=Loads at Midway. If 1, the Switch will be movable by environment stuff, such as dropping down when bricks below it are destroyed, or riding along a conveyor belt. If 4, the Switch will only show if the level has been started from a midway point. • Delay on Multi Use: list at nybble 5: 0=Instantaneous (No Delay),2=Short Delay,3=Long Delay,1=Very Long Delay. [check this nybble]This will set how long the Switch takes to pop up after the Timer expires on a Multi Use Switch • Non-Timed Event: list at nybble 6: 0=Timed,1=Non Timed. "When timed, switch starts in start or stop. While timed, it is opposite." I dunno what this means - Hiccup • Switch Mode: list at nybble 8: 0=Activates Target (Switches Event State),1=Deactivates Target (Switches Event State). Switch press-status can be ended by hitting the opposite sw.? • Usage Mode: list at nybble 9: 0=Single Use,1=Multi Use,2=Unknown. 2 is unused. • Shift ½ Block Right: checkbox at nybble 10 with mask 1 • Upside Down: checkbox at nybble 11 with mask 1. If this is checked, the Switch will be facing down. Upside down Switches cannot fall. |
|
⇨
|
By Hiccup on 03-31-15, 01:11 pm |
Category 'Event controllers', known, fully documented |
This sprite shares its image file with P-switch, ? switch and Bowser battle switch. |
Data files: • /obj/I_switch_ncg.bin |
Sprite fields: • Triggering Event ID: value at nybble 0-1. [confirm latter sentence] If this ID is set, the Switch will only show while this Event ID is activated. Slightly buggy if used with Multi Use. [confirm latter sentence] • Target Event ID: value at nybble 2-3 • Falls, Loads at Midway: list at nybble 4: 0=None,1=Falls,4=Loads at Midway. If 1, the Switch will be movable by environment stuff, such as dropping down when bricks below it are destroyed, or riding along a conveyor belt. If 4, the Switch will only show if the level has been started from a midway point. • Delay on Multi Use: list at nybble 5: 0=Instantaneous (No Delay),2=Short Delay,3=Long Delay,1=Very Long Delay. [check this nybble]This will set how long the Switch takes to pop up after the Timer expires on a Multi Use Switch • Non-Timed Event: list at nybble 6: 0=Timed,1=Non Timed • Switch Mode: list at nybble 8: 0=Activates Target (Switches Event State),1=Deactivates Target (Switches Event State). Switch press-status can be ended by hitting the opposite sw.? • Usage Mode: list at nybble 9: 0=Single Use,1=Multi Use,2=Unknown. 2 is unused. • Shift ½ Block Right: checkbox at nybble 10 with mask 1 • Upside Down: checkbox at nybble 11 with mask 1. If this is checked, the Switch will be facing down. Upside down Switches cannot fall. |
|